Heavy Duty Steering Box Arm Removal Tool For Mac

Posted on  by

1-24 of 361 results for 'Steering & Suspension Tools' Skip to main search results. Heavy Duty Ball Joint Press & U Joint Removal Tool Kit with 4x4 Adapters, for Most 2WD and 4WD Cars and Light Trucks. Pitman Arm Puller, Tie Rod End Tool Set for Front End Service, Splitter Removal. Irvan-Smith, Inc.: Do-It-Yourself Kits:Start from scratch, design and build your you very own pit carts, pit wagon or tire rack with our Do-It-Yourself Kits. Kits allow you to determine the size of the cart and incorporate any toolbox that you may already have readily available. We also offer Bottom Frames giving you a starting point and you build it from the frame up.  Also.

5 INTRODUCTION This service manual covers only repairs to Sheppard M -Series steering gears. The vehicle manufacturer's service manual should be used for removal and installation instructions of the steering gear, power steering pump, and all other steering. Easily remove even the most stubborn pitman arms on Sheppard M100 gearboxes. Eliminates dangerous hammering and cutting torch methods. May be used with up to a 3/4″ impact tool. Reason is the thrust on the end of the pitman arm is not made to take much pulling out of the box pressure.If you ever in that box you will know what I am talking about. There was two different boxes that the B models used.As stated heat is last resort to do.There is people in the grave yard that was caused by using heat on steering componets.

The Currie F9 fabricated 9-inch axle set for Jeep Wrangler JL/JLU delivers off-road race-inspired design with the strength, and durability enthusiast desire. The F9 fabricated housing features a heavy-duty CNC formed and gusseted center section that reduces unsprung weight by more than 50 pounds compared to a cast center. The F9 is designed for severe off-road use with up to 40-inch tires and V8 conversion horsepower.


Removal

Axle Set Details:

  • Fully Assembled Front And Rear Low-Pinion Currie F9 Axles
  • 70-Inch Width Provides Improved Clearance For Large Tires
  • 8-Lug Wheel Bolt Pattern For Ultimate Reliability
  • Satin Black Powder Coat Finish For Long Lasting Protection
  • Includes ARB Air Locker And Choice Gear Ratio
  • Includes Currie Racing Gear Oil

Exclusive F9 Features:

  • Currie Race-Inspired Fabricated 9-Inch Housing Delivers Strength And Performance In A Lightweight Package
  • Currie 9-Inch Low-Pinion 3rd. Member Provides Unmatched Gear Strength, Reliability And Serviceability

FOR DIESEL AND 4 CYLINDER E-TORQUE EQUIPED VEHICLES CALL SALES AT (714) 528-6957

Correctly and Safely removing and reinstalling a pitman arm can be more difficult than it first appears. Aside from the potential for injury reinstalling it incorrectly will impact on the performance of the steering system and the life of the components.

For instance incorrect installation can cause issues with wheel cuts on a vehicle, so it is important to get it right. The best start to getting it right is having the correct tools for the job.

Tools

There are a number of specialist tools which are recommended for the safe removal and reinstallation of the pitman arm,

Heavy duty steering box arm removal tool for mac safe

Ball Joint Removal Kits – Hydrosteer Part Number 43-20245 (Large) and 43-20270 (Small)

Ball Joint Remover Kit – Small

Pitman Arm Puller – Hydrosteer Part Number J43744 or 3591842K (Multiple versions available ask our technical staff for help)

Heavy Duty Steering Box Arm Removal Tool For Mac Safe

Torque Wrench

Impact Wrench 3/4″ or Larger.

The key steps in the pitman arm removal process are

  • Remove the draglink using a ball joint remover device.
  • Remove the retainer bolt.
  • Apply grease to the face of the sector shaft and position the pitman arm puller on the center line of the sector shaft.
  • Tighten puller bolt, a tap with a hammer on the pitman arm may be required to release the tapers.

The key steps in the pitman arm installation process are

  • Place pitman arm over the sector shaft aligning the timing marks
  • Apply antiseize compound to the retainer nut
  • Torque the retainer nut to the torque specified on the nut
  • Continue to torque until locking tabs align with retainer nut
  • Punch locking tabs into place.

Heavy Duty Steering Box Arm Removal Tool For Mac Free

The video below, from R.H. Sheppard runs through the correct removal and installation process for a pitman arm.

Removing and Installing a Pitman Arm